CCNA 5.0 Bài lab cấu hình vlan trunk vtp intervlan routing TN

CCNA 5.0 Bài lab cấu hình vlan trunk vtp intervlan routing TN

ccna 5.0 vlan trunk vtp routing

CCNA 5.0 Cấu hình chia subint trên R1 để định tuyến giữa các vlan

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hos
Router(config)#hostname R1
R1(config)#ena
R1(config)#enable pas
R1(config)#enable password cisco
R1(config)#li
R1(config)#line con
R1(config)#line console 0
R1(config-line)#pas
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#exit
R1(config)#li
R1(config)#line vt
R1(config)#line vty 0 4
R1(config-line)#pas
R1(config-line)#password cisco
R1(config-line)#exit
R1(config)#ban
R1(config)#banner m
R1(config)#banner motd “R1-cuongnm”
R1(config)#int f0/0
R1(config-if)#no shut

R1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R1(config-if)#exit
R1(config)#int f0/0.10
R1(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up

R1(config-subif)#en
R1(config-subif)#encapsulation d
R1(config-subif)#encapsulation dot1Q
% Incomplete command.
R1(config-subif)#encapsulation dot1Q 10
R1(config-subif)#ip add
R1(config-subif)#ip address 192.168.10.1 255.255.255.0
R1(config-subif)#exit
R1(config)#int f0/0.20
R1(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.20, changed state to up

R1(config-subif)#en
R1(config-subif)#encapsulation d
R1(config-subif)#encapsulation dot1Q 20
R1(config-subif)#ip add
R1(config-subif)#ip address 192.168.20.1 255.255.255.0
R1(config-subif)#exit
R1(config)#int f0/0.30
R1(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.30, changed state to up

R1(config-subif)#en
R1(config-subif)#encapsulation d
R1(config-subif)#encapsulation dot1Q 30
R1(config-subif)#ip add
R1(config-subif)#ip address 192.168.30.1 255.255.255.0
R1(config-subif)#exit
R1(config)#exit
R1#
%SYS-5-CONFIG_I: Configured from console by console

R1#wr
Building configuration…
[OK]
R1#

CCNA 5.0 Cấu hình S1 vtp server

Switch>
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hos
Switch(config)#hostname S1
S1(config)#ena
S1(config)#enable pas
S1(config)#enable password cisco
S1(config)#li
S1(config)#line con
S1(config)#line console 0
S1(config-line)#pas
S1(config-line)#password cisco
S1(config-line)#login
S1(config-line)#exit
S1(config)#li
S1(config)#line v
S1(config)#line vty 0 15
S1(config-line)#pas
S1(config-line)#password cisco
S1(config-line)#login
S1(config-line)#exit
S1(config)#ban
S1(config)#banner m
S1(config)#banner motd “S1-cuongnm”
S1(config)#vlan 10
S1(config-vlan)#na
S1(config-vlan)#name CB
S1(config-vlan)#exit
S1(config)#vlan 20
S1(config-vlan)#na
S1(config-vlan)#name SV
S1(config-vlan)#exit
S1(config)#vlan 30
S1(config-vlan)#na
S1(config-vlan)#name QT
S1(config-vlan)#exit
S1(config)#vtp
S1(config)#vtp m
S1(config)#vtp mode ser
S1(config)#vtp mode server
Device mode already VTP SERVER.
S1(config)#vt
S1(config)#vtp d
S1(config)#vtp domain cisco.com
Changing VTP domain name from NULL to cisco.com
S1(config)#vtp pa
S1(config)#vtp password cisco
Setting device VLAN database password to cisco
S1(config)#int ra
S1(config)#int range f0/1 ?
, comma
– hyphen
<cr>
S1(config)#int range f0/1-3
S1(config-if-range)#sw
S1(config-if-range)#switchport m
S1(config-if-range)#switchport mode tr
S1(config-if-range)#switchport mode trunk

S1(config-if-range)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up

S1(config-if-range)#exit
S1(config)#exit
S1#
%SYS-5-CONFIG_I: Configured from console by console

S1#wr
Building configuration…
[OK]
S1#

S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#int vlan 30
S1(config-if)#
%LINK-5-CHANGED: Interface Vlan30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan30, changed state to up

S1(config-if)#no shut
S1(config-if)#ip add
S1(config-if)#ip address 192.168.30.11 255.255.255.0
S1(config-if)#exit
S1(config)#ip de
S1(config)#ip default-gateway 192.168.30.1
S1(config)#exit
S1#
%SYS-5-CONFIG_I: Configured from console by console

S1#wr
Building configuration…
[OK]
S1#

CCNA 5.0 Cấu hình S2 vtp client

Switch>
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hos
Switch(config)#hostname S2
S2(config)#ena
S2(config)#enable pas
S2(config)#enable password cisco
S2(config)#li
S2(config)#line con
S2(config)#line console 0
S2(config-line)#pas
S2(config-line)#password cisco
S2(config-line)#login
S2(config-line)#exit
S2(config)#li
S2(config)#line vt
S2(config)#line vty 0 15
S2(config-line)#pas
S2(config-line)#password cisco
S2(config-line)#login
S2(config-line)#exit
S2(config)#ban
S2(config)#banner m
S2(config)#banner motd “S2-cuongnm”
S2(config)#vtp mo
S2(config)#vtp mode clie
S2(config)#vtp mode client
Setting device to VTP CLIENT mode.
S2(config)#vtp do
S2(config)#vtp domain cisco.com
Domain name already set to cisco.com.
S2(config)#vt
S2(config)#vtp p
S2(config)#vtp password cisco
Setting device VLAN database password to cisco
S2(config)#int f0/1
S2(config-if)#sw
S2(config-if)#switchport mo
S2(config-if)#switchport mode tr
S2(config-if)#switchport mode trunk
S2(config-if)#do show vlan

VLAN Name Status Ports
—- ——————————– ——— ——————————-
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24, Gig1/1
Gig1/2
10 CB active
20 SV active
30 QT active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
—- —– ———- —– —— —— ——– —- ——– —— ——
1 enet 100001 1500 – – – – – 0 0
10 enet 100010 1500 – – – – – 0 0

S2(config-if)#exit
S2(config)#int vlan 30
S2(config-if)#
%LINK-5-CHANGED: Interface Vlan30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan30, changed state to up

S2(config-if)#no shut
S2(config-if)#ip add
S2(config-if)#ip address 192.168.30.12 255.255.255.0
S2(config-if)#exit
S2(config)#ip de
S2(config)#ip default-gateway 192.168.30.1
S2(config)#int f0/2
S2(config-if)#sw
S2(config-if)#switchport m
S2(config-if)#switchport mode ac
S2(config-if)#switchport mode access
S2(config-if)#sw
S2(config-if)#switchport ac
S2(config-if)#switchport access v
S2(config-if)#switchport access vlan 10
S2(config-if)#int f0/3
S2(config-if)#sw
S2(config-if)#switchport mo
S2(config-if)#switchport mode ac
S2(config-if)#switchport mode access
S2(config-if)#sw
S2(config-if)#switchport ac
S2(config-if)#switchport access v
S2(config-if)#switchport access vlan 20
S2(config-if)#exit
S2(config)#exit
S2#
%SYS-5-CONFIG_I: Configured from console by console

S2#wr
Building configuration…
[OK]
S2#